-768x1469.jpg)
Spring tension testing machine is widely deployed in petroleum-chemical industries, mechanical manufacturing, plastic & rubber processing, adhesive laboratories, ceramic and building-material factories, metal material analysis labs, universities, research institutes, technical-supervision departments and quality-inspection stations. As dedicated test hardware for spring products, this equipment performs physical-mechanical property tests for extension springs, compression springs, leaf springs, circlips, flat springs, disc springs, conical springs, composite springs, gas springs, die springs and special-shaped springs. Typical test modes include peeling test, tensile test, tearing test, puncture test, compression resistance test, bending test, shear resistance test, and constant-load testing.
Like all precision mechanical instruments, spring tension testing machines will suffer mechanical wear, unexpected malfunctions and component damage during long-term daily operation. If operators cannot identify root causes quickly, unplanned downtime, inaccurate test readings and invalid spring-quality reports will occur. This blog sorts out common faults and practical troubleshooting solutions for spring tension testing machines, helping lab technicians and quality-control engineers resolve typical equipment issues efficiently.
1. Pointer vibrates or moves intermittently under loading
When you run spring tensile load test, the dial pointer shakes violently or stops and jumps irregularly:
- Worn clutch gear: Repair or directly replace the worn clutch gear assembly.
- Worn leather washer or internal spring inside friction disc: Install brand-new leather washer and friction-disc spring components.
- Displaced operating handle: Readjust the operating handle to achieve proper engagement with the gear alveolus.
2. Pointer fails to return-to-zero after changing pendulum weights
This fault frequently appears during multi-range spring force measurement after swapping A/B/C pendulum weights:
- Uneven machine installation: Apply a spirit level to re-level the whole spring tension testing machine base.
- Pendulum weight out of vertical alignment: Hang weight-A only, fine-tune the counterbalance weight until the pendulum keeps perfect vertical posture.
-133x300.jpg)
3. Pendulum weight returns too fast or too slowly
Improper pendulum reset speed distorts spring compression-tension test curve:
- Mis-adjusted buffer valve gear position: Set buffer valve to suitable working position.
- Hydraulic oil viscosity out of specification: Low-viscosity oil causes fast pendulum fallback; high-viscosity oil leads to slow return. Replace hydraulic oil with correct viscosity grade.
- Contaminants inside buffer valve, oil pipeline or hydraulic fluid: Fully clean buffer valve and oil pipelines, then replace contaminated hydraulic oil.
4. Slow or unstable pointer zero-return performance
Symptoms: Pointer sticks, hesitates or fluctuates when returning back to zero position on analog spring tester:
- Corrosion or oil contamination on pointer bearing and main-shaft bearing: Clean bearing assemblies or replace defective bearings.
- Bent rack gear or poor meshing status between rack and pinion: Straighten deformed rack; clean, trim and repair gear and sheave transmission parts.
- Dirt accumulated inside buffer valve: Disassemble and thoroughly clean the buffer valve chamber.
5. Positive reading deviation (indicated force value higher than real load)
Positive reading error misleads spring stiffness and maximum-load assessment:
- Loose short-arm cutting edge: Tighten fastening screws for short-arm knife-edge component.
- Under-weight pendulum bob: Add counterweight mass for pendulum weights; make balance adjustment covering weight A, weight B and weight C synchronously.
6. Negative reading deviation (indicated force value lower than real load)
Excessive mechanical friction among moving parts is the primary trigger for negative reading error:
- Extra friction resistance on pointer bearing, pendulum-shaft bearing and force-measuring transmission set: Clean and fine-adjust bearings and force-measuring transmission assemblies to eliminate abnormal friction.
- Excessive friction from upper chuck, driven-pointer spring-plate and chart-recording device: Tune tightness of upper chuck and driven-pointer spring plate; service plotting-device components to cut down redundant friction.
- Stiff joint between piston rod and pendulum lever: Lubricate and adjust connecting parts to guarantee flexible movement.
7. Driven pointer jams or shifts randomly
Common fault on dial-type spring tension-compression testing machine:
- Improper spring-plate tension or too-large gap friction between driven pointer and indicator dial: Adjust spring-plate spring force and clearance gap between driven pointer and dial plate.
- Unbalanced mass on two ends of driven pointer: Tweak end-point weights of driven pointer to reach mechanical balance.
8. Irregular & random reading deviation
Unpredictable force-value fluctuation is one of the trickiest issues for spring-quality inspection:
- Oil dirt, surface wear or burr defects on rack and pinion gears: Remove dirt and burrs; revise contact points of rack-gear meshing area when out-of-tolerance occurs; replace rack-pinion set if correction cannot eliminate deviation.
- Machine foundation out-of-level: Re-level the complete testing-machine unit.
- Bent rack bar: Straighten or swap out deformed rack; adjust clearance of rolling sheave components.
Importance of Periodic Preventive Maintenance
After resolving above-mentioned typical malfunctions, lab teams should carry out regular preventive maintenance schedules for the spring tension testing machine. Routine cleaning, lubrication, component inspection and periodic calibration effectively extend equipment service life, lower unexpected repair frequency and guarantee repeatable, reliable spring-test data for your production quality control workflow.
Conclusion
Spring tension testing machine acts as core quality-control hardware for verifying mechanical performance of all categories of industrial springs. Most typical malfunctions originate from mechanical wear, contamination, mis-alignment and incorrect setting rather than severe hardware breakdown. Systematic fault-check steps, timely component replacement and strict regular maintenance can avoid most reading-error problems and unexpected downtime. If you are searching for reliable, high-accuracy spring-test instruments and professional application support, Mikrosize delivers well-engineered spring tension-compression testers, together with complete technical guidance, calibration service and after-sales troubleshooting assistance for manufacturing plants and research laboratories worldwide. Proper operation plus standardized maintenance will maximize your testing-machine performance and secure credible spring-product test results.
-150x150.jpg)







